 |
|
SyndicateSearch Our Store Navigation |
Multiplex USA Funjet
The new FunJET from Multiplex USA is the latest in their continuing line of smallish jet type models designed for all-out fun. The FunJET assembles from just seven molded foam pieces, and it can easily be completed in a relaxed evening. I spread it across two evenings to install the radio and to add the decals. Once at the field, you will find the FunJet a very nice flying model that is a perfect compromise between all-out performance and duration. It is faster than most models at our field, including several other ARF type flying wings, and scores very high on the fun scale.
TIPS FOR SUCCESS
I used a pair of Hitec HS-65HB servos and they were a press-fit into the servo pockets. I pressed my servos into place and then smeared a little hot melt glue on the edges to hold them in place. You will find that the servo leads are just long enough to reach into the fuselage. Six-inch servo extensions are just the right length for reaching the receiver at the leading edge of the wing. I tied the extensions to the servo leads and then taped them down before closing up the fuselage. Reconnecting an extension after the fuselage is closed would be very challenging.
The elevons are part of the wing structure and are hinged by a thin section of Elapor. This system works very well, but you will need to cut the tips free from the wing and open up an appropriate gap. I recommend keeping them attached until after you set up the pushrods. This helps establish the neutral setting. I then sliced the ends free with a #11 X-Acto blade, and opened the gap using a piece of folded 120-grit sandpaper.
In the manual, illustration #17 recommends placing the battery near the leading edge of the wing and the receiver all the way forward. I didn’t like the idea of having the receiver so vulnerable in a crash, and a quick CG check confirmed that the battery wants to be all the way forward. Be sure to use Velcro to secure the battery. The CG is critical for flying wings, and if the battery slides aft on launch, the flight will be over long before you planned.
CONCLUSION Links Multiplex, www.multiplexusa.com, (858) 748-6948 Venom Air Corps., www.venom-aircorps.com, (800) 705-0260 W.S. Deans, www.wsdeans.com, (714) 828-6494 ZAP is manufactured by Pacer Technology, www.zapglue.com ZLog recording altimeter, Hexpert Systems, www.hexpertsystems.com AIRBORNE I’m always a little nervous about hand launching pusher designs, but this one is about as mild as they come. Because the prop barely extends below the back of the fuselage, once you release the model, your hand will be well clear of the prop. If you feel more comfortable doing so, you can easily launch the FunJET with the power off, then throttle up once it is gliding clear.
Despite its speed, the FunJET should be easy to fly for anyone who has a bit of aileron experience in their logbooks. You certainly don’t need full throttle all the time and if you can stand it, backing off will greatly extend the duration. I open it up just for high-speed passes and aggressive climbs. Like any aircraft, the FunJET can make tighter turns when slowed up a bit, and keeping it in close certainly helps with the impression of speed. The roll rate with the recommended throws is quick but not blistering. I was able to stop it at the desired bank angles with just a little practice. The elevator response seems just right. There is enough throw to pitch it up aggressively, yet its manners remain mild with little tendency to snap out. With unlimited climb available, loops can be any size you want. My personal record starting just above the field is over 1,000 feet at the top; more wouldn’t be any trouble, but you’ll need your binoculars to see it. The FunJET is limited to aileron-elevator aerobatics since it has no rudder, but that is not really an issue for this design. No one is going to confuse this jet for a 3D hovering ship. The FunJET is all about speed and carving big arcing turns, or drilling holes in the sky while rolling upward out of sight. You will be in for a treat when it comes time to land. The FunJET complements its high-speed performance with an outstanding glide and smooth nose-high handling. You can glide in easily power off, controlling the sink rate with the elevator, and a touch of power can stretch the glide to set it down right at your feet. With a little power and the nose held up slightly, the FunJET will float right in for an easy landing wherever you choose. The FunJET handles predictably with exciting performance, and puts a smile on my face every time I fly it. I wouldn’t change a thing.
Posted Date:
10-February-2011 (All day) Status:
Posted To Social Media
|
|||||||
Once the power comes on, hold on tight! The FunJET lives up to its name in just the first few feet as it accelerates and climbs out. You can go vertical as soon as you want and still climb out of sight. My ZLog altimeter shows it going up at over 2,200 feet per minute in a stabilized climb; that’s a pretty smart climb for a little foamie with a toothpick-like speed prop on it. Straight and level on a high-speed strafing run, the FunJET really scoots across the field and arcs back up into the blue for as far as you can see it.